Exactly How to Remove and Change a Tub.
Exactly How to Remove and Change a Tub.
Blog Article
How do you feel in relation to How to Install a Bathtub?
Installing a tub isn't exactly brain surgery, but it does call for solid plumbing, woodworking, as well as occasionally, tiling skills. Changing an old bath tub with a new one is additionally a moderately difficult job. If the old tub is readily accessible, the project can move easily; if you have to open a wall to get rid of the old tub as well as place the new tub, the job is much harder. In either instance, the job is within a residence handyman's abilities, although you will require a helper to move out the old bathtub and embeded in the new one. Make certain you have actually qualified yourself for the work and fit trying it. Instead of working with a contractor to take over a halfway-completed task, it is much better to consider utilizing one prior to you start. Possibilities are you might require a specialist plumber to make tube connections.
This short article will certainly aid you install a new bath tub in your bathroom if you have already acquired a brand-new tub and do not require to change the arrangement of your previous supply of water pipelines.
Your devices and also product list should comprise the following:
Getting ready for the Setup
First of all, the supporting framework provided with the bathroom must be fitted (if needed) according to the maker's directions. Next off, fit the faucets or mixer to the tub. When suitable the tap block, it is very important to make certain that if the faucet comes with a plastic washer, it is fitted in between the bath as well as the taps. On a plastic bath, it is also sensible to fit a supporting plate under the faucets device to stop pressure on the tub.
Fit the versatile tap connectors to the bottom of the two taps making use of 2 nuts and also olives (in some cases supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the outlet with the hole in the bath. Utilize the nut supplied by the producer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. Make certain you utilize all of the provided washers.
Attach the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bathroom need to currently be ready to be suited its final position.
Removing Old Touches
If you need to change old taps with brand-new ones as a part of your installation, after that the first thing you ought to do is separate the supply of water. After doing so, activate the taps to drain pipes any type of water remaining in the system. The procedure of removing the existing taps can be fairly troublesome as a result of the restricted accessibility that is typically the case.
Utilize a container wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipes to the taps. Have a towel ready for the continuing to be water that will originate from the pipes. As soon as the supply pipelines have actually been removed, utilize the same device to loosen the nut that holds the faucets onto the bath/basin. You will require to quit the single faucets from transforming during this procedure. As soon as the taps have actually been gotten rid of, the holes in the bath/basin will need to be cleaned of any type of old securing compound.
Prior to going on to fit the brand-new taps, contrast the pipe links on the old taps to the brand-new taps. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the new faucets to fit.
Mounting the Bathtub
Utilizing both wooden boards under its feet, position the bathtub in the called for position. The wood boards are useful in equally spreading the weight of the tub over the location of the boards rather than focusing all the weight onto 4 small factors.
The next goal is to ensure that the tub is leveled all round. This can be achieved by checking the level and also changing the feet on the tub until the spirit level reviews level.
To mount taps, fit all-time low of the outermost flexible tap port to the proper supply pipeline by making a compression join; then do the exact same for the various other faucet.
Switch on the water system and also check all joints as well as brand-new pipework for leakages and tighten them if required. Load the bathtub as well as also check the overflow outlet as well as the regular electrical outlet for leaks.
Lastly, take care of the bathroom paneling as defined in the maker's user's manual. Tiling and sealing around the bathtub should wait until the tub has been utilized at the very least when as this will certainly settle it into its last placement.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic adapter to stop damages to the string. One end of the connector fits on the plastic tail of the tap as well as the various other end supplies a link to the existing supply pipelines.
If you require to fit a monobloc, after that you will certainly need minimizing couplers, which links the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next off, place the tap in the placing opening in the bath/basin making sure that the washing machines are in place in between the tap and the sink. Secure the faucet in position with the manufacturer provided backnut. As soon as the tap is securely in position, the supply pipelines can be connected to the tails of the faucets. The faucets can either be connected by utilizing corrugated copper piping or with typical faucet adapters. The former kind must be connected to the faucet finishes first, tightening up only by hand. The supply pipes can later on be linked to the various other end. Tighten up both ends with a spanner after both ends have been linked.
Tiling Around the Bathtub
In the location where the bathroom meets the tile, it is needed to seal the accompanies a silicone rubber caulking. This is very important as the fitting can relocate enough to crack a stiff seal, triggering the water to penetrate the wall surface in between the bath and also the tiling, causing problems with wetness and feasible leaks to the ceiling listed below.
You can select from a selection of coloured sealants to assimilate your fixtures and installations. They are sold in tubes and also cartridges, as well as can sealing voids as much as a size of 3mm (1/8 inch). If you have a larger space to load, you can fill it with spins of soaked paper or soft rope. Remember to constantly fill the tub with water before securing, to allow for the motion experienced when the bathtub is in usage. The sealer can crack relatively very early if you do not take into consideration this movement before securing.
Additionally, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are additionally conveniently offered on the marketplace. It is advisable to fit the floor tiles using water-resistant or water-proof adhesive as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
:max_bytes(150000):strip_icc()/installing-a-tub-or-shower-surround-2718986-hero-40160398595d4544b639b3398cdb247c.jpg)
Do you appreciate more info about A Step-by-Step Guide to Installing a Bathtub? Leave a remark below. We'd be glad to see your feelings about this review. We are looking forward that you visit us again in the near future. Please set aside a second to distribute this blog if you liked it. Bless you for your time. Please visit our site back soon.
Get Started Report this page